Tim-bor can be used as a wood preservation, insecticide or fungicide.
Pest management professionals can apply it to the wood as a dust, liquid,
foam or mist for both interior and exterior use.
Formulated with a concern for the environment, Tim-bor is used for the
control of carpenter ants, drywood termites, wood decay fungi and wood
boring beetles. As water soluble borate powder, Tim-bor diffuses into the
wood and acts as a wood insecticide, fungicide and preservative. Tim-bor
won't break down over time like most organic compounds, therefore offering
longer lasting protection. Best of all, Tim-bor is easy to mix, virutally
odorless and has no known resistance. |
timbor®
Professional
Insecticide and Fungicide
Only for sale to, use and storage by
professional pest control operators
A preservative for protection and
treatment of wood against fungal decay and wood destroying insects
including termites
For the prevention and remedial control
of wood**infesting organisms including:
Termites, Drywood Termites, Wood
Destroying Beetles, Decay Fungi and Carpenter Ants
**Also for Wood Foam Composite Structural
Components
Active Ingredient:
Disodium Octaborate Tetrahydrate
(Na2B8O13.4H2O).......98%
Other
Ingredient+.......................................................................2%
Total…............... ..........
............... ......................... ................100%
+Contains 2% H2O - Absorbed Moisture
EPA Reg. No. 64405-8
EPA Est. 64405-TN-1
Keep Out Of Reach Of
Children
CAUTION
PRECAUTIONARY STATEMENTS
Hazards To Humans & Domestic Animals
Caution:
Harmful if swallowed or inhaled. Causes moderate eye irritation. Avoid
contact with eyes or clothing. Avoid breathing dust. Thoroughly wash with
soap and water after handling. Remove contaminated clothing and wash
clothing before reuses.
FIRST AID
|
If swallowed |
- Immediately call a poison
control center or doctor for treatment advice.
- Have person sip a glass of
water if able to swallow.
- Do not induce vomiting unless
told to do so by the poison control center or doctor.
- Do not give anything by mouth
to an unconscious person.
|
|
If Inhaled |
- Move person to fresh air.
- If person is not breathing,
call 911 or an ambulance, then give artificial respiration,
preferably by mouth-to-mouth, if possible.
- Call a poison control center or
doctor for further treatment advice.
|
|
If in Eyes |
- Hold eye open and rinse slowly
and gently with water for 15-20 minutes.
- Remove contact lenses, if
present, after the first 5 minutes, then continue rinsing eye.
- Call a poison control center or
doctor for further treatment advice.
|
|
Have the product
container or label with you when calling a poison control center or
doctor or going for treatment.You may also contact 800-424-9300 for
emergency medical treatment information. |
Environmental Hazards
This pesticide is
toxic to fish and wildlife. Do not apply directly to water, to areas where
surface water is present or to intertidal areas below the mean high water
mark. Do not contaminate water when cleaning equipment or disposing of
equipment washwaters.
NOTICE
Read and understand
the entire label before using. Use only according to label
directions.Before buying or using this product, read Warranty Limitations
and Disclaimer statement found elsewhere on this label. If terms are
unacceptable, returned unopened package to seller for full refund of
purchase price. Otherwise, use by the buyer or any other user constitutes
acceptance of the terms under Warranty Limitations and Disclaimer.
DIRECTIONS FOR USE
It is a violation of
Federal law to use this product in a manner inconsistent with its
labeling.
Storage and Disposal
Do not contaminate
water, food or feed by storage or disposal. Pesticide Storage:
Store in a dry place. Do not Store where children or animals may gain
access. Pesticide Disposal: Wastes resulting from the use of this
productmay be disposed of on site or at an approved waste disposal
facility. Container Disposal: Triple rinse (or equivalent) then
offer for recycling or reconditioning, or puncture and dispose of in a
sanitary landfill, or incineration, or if allowed by state and local
authorities, by burning. if burned, stay out of smoke. |
|
Storage and Disposal
Do not contaminate water, food or feed by storage or
disposal. Pesticide Storage: Store in a dry place. Do not Store
where children or animals may gain access. Pesticide Disposal:
Wastes resulting from the use of this productmay be disposed of on
site or at an approved waste disposal facility. Container Disposal:
Triple rinse (or equivalent) then offer for recycling or
reconditioning, or puncture and dispose of in a sanitary landfill, or
incineration, or if allowed by state and local authorities, by
burning. if burned, stay out of smoke. |
General Information
TIM-BOR Professional is a water soluble, inorganic
borate salt with insecticidal and fungicidal properties effective against
wooddestroying organisms including the target pests listed below. Apply
TIM-BOR Professional as a liquid solution, powder or foam. TIM-BOR
Professional is an effective treatment for wood (and woodfoam
composite structural components) to kill and prevent infestations of decay
fungi including white rot, brown rot (i.e., Poria) and wet rots. This
product may be used for preventative treatment (before signs of
infestation), for wood in existing structures and for remedial treatment
of infested wood in existing structures. TIM-BOR Professional is
also effective for the prevention and control of wood destroying insects
such as, but not limited to, the following organisms:
Subterranean Termites (Reticulitermes, Heterotemes,
Coptotermes (Formosan)), Drywood Termites (Kalotermes, Incisitermes),
Dampwood Termites (Zootermopis), Powderpost Beetles (Lyctidae),
"False" Powderpost Beetles (Bostrichidae), Deathwatch and
Furniture Beetles (Anobiidae), Old House Borers, Longhorn Beetles
(Cerambycidae), Carpenter Ants (Camponotus), Bark and Timber
Beetles (Scolytidae)
TIM-BOR Professional is recommended for wood and
cellulose material in accordance with the specific treatment methods
described herein. TIM-BOR Professional is effective for all
interior and exterior wood (and wood-foam composite structural components)
that will be protected from excessive rain and not in direct contact with
the soil. Types of wood include, but are not limited to, all types of
lumber, logs and plywood. This product kills wood-destroying organisms.
Some etching of treated wood may occur from organisms before they die. Do
not apply TIM-BOR Professional to wood or cellulose material that
has been painted, varnished or sealed. For best results, apply TIM-BOR
Professional to bare wood. Use soap and water to clean application
equipment.
Preparation of Treatment Solutions
10% TIM-BOR Professional Liquid Solution: To
prepare solution, add approximately 80% of the required volume of water to
the mixing vessel. While stirring, gradually add 1.0 pound of TIM-BOR
Professional for each gallon of treating solution required. Add
remaining water to the solution and stir until the entire product has
dissolved.
15% TIM-BOA Professional Liquid Solution: prepare
solution as above, but gradually add 1.5 pounds of TIM-BOR Professional
for each gallon of treatment solution needed. Use this solution as soon as
possible and do not store for an extended length of time.
15% TIM-BOR Professional Foam: Prepare a 15% liquid
solution as described above and also add a surfactant-foaming agent.
Generally 1-2 ounces of a foaming agent, added to the 15% liquid solution,
produces a dry foam with the desired expansion ratio of approximately 20
to 1 (20 gallons of foam per 1 gallon of liquid solution). The TIM-BOR
Professional foam should be of a "dry" consistency that adheres to
wood surfaces so that run-off is minimized. A "wet" foam may damage
wallboard or other building components. Refer to the individual foam
equipment manufacturer's manual and the surfactant's label for specific
instructions. Wash and rinse all equipment after each use. |
General Application Instructions
TIM-BOR Professional as a liquid solution: TIM-BOR
Professional liquid applications may be made to wood structures
including decks, fences, steps, sheds, barns and other outbuildings such
structures must be protected from excess rain. On wood with drier than
normal moisture content, apply by brush or spray two applications of a 10%
solution to wood surfaces. On wood with normal moisture content, apply by
brush or spray one application of a 15% solution to wood surfaces.
Application may also be made by drilling and then injecting the solution
under pressure into sound wood or into the insect galleries of infested
wood. TIM-BOR Professional may be applied as a foam to wood
surfaces or injected into wall voids or insect galleries.
Remedial and Preventative Treatment
TIM-BOR Professional Solutions for the Control
of Wood Destroying Organisms and to Kill Active Infestations of Termites,
Powderpost Beetles and Wood Decay Fungi: For remedial control of wood
attacking organisms or for the protection of wood against future
infestations, two applications of a 10% liquid solution are normally
required. One application of a 15% liquid solution may be used. Apply
TIM-BOR Professional solutions by brush or spray at the rate of 5
gallons of liquid solution per 1000 square feet of wood surface area.
Thoroughly wet wood surface area. Application may also be made by drilling
and then injecting the liquid solution under pressure into sound wood or
until run-off is observed coming from entry/exit holes of infested wood.
TIM-BOR Professional Powder to Kill and Control Wood
Destroying Organisms, Such as Termites and Carpenter Ants: Apply
TIM-BOR Professional as is to wood members by drilling and injecting
the powder into galleries or by dusting generously on wood surfaces.
TIM-BOR Professional powder can also be injected or dusted into wall
voids such as between studs, block voids, box sills, eaves, attics,
soffets, etc. Apply TIM-BOR Professional powder to these areas at
the rate of 0.5 ounce (12-14 grams) per square foot.
TIM-BOR Professional Foam: In wall voids, inject
enough dry foam to contact wood surfaces of studs in the wall or the
entire desired target area. Apply foam, where possible, to abutting wood
surfaces and between wood joints. Apply the foam so that all accessible
wood surfaces are covered with foam. TIM-BOR Professional foam can
also be injected into insect galleries until run-off is observed.
Warranty Limitations and Disclaimer
Because of varying conditions affecting the use and
application, manufacturer warns buyer that these may impair or vary the
results or effects of the use of this product. In any event, complete
prevention of decay or insect infestation is not guaranteed. Neither the
manufacturer nor seller shall be liable in respect to any injury or damage
suffered by reason of the use of this product for a purpose not indicated
by the label or when used contrary to the directions or instructions
hereon or with respect to breach of any warranty not expressly specified
herein. Buyer accepts this material subject to these terms and assumes all
risk of usage and handling except when used or handled in accordance with
this label.
Nisus Corporation
100 Nisus Drive
Rockford, TN 37853 .(800) 264-0870
www.nisuscorp.com
Made in the U.S.A.
'TIM-BOR and the House Design trademark are registered
trademarks of U. S. Borax Inc. and are used under license. Nisus is a
registered trademark of Nisus Corporation.
[Home]
[Up] |
|
You can pay for
your order in different ways:
-
Online
American Express Card Payment.
You can pay for
our mold products and services online with your AMEX card by
clicking on the checkout button below.
-
Online Visa, MasterCard, American
Express, Discover Card, PayPal, or checking account payment with
SHOPPAL Online
Catalog or Shopping Cart.
You can pay for
our mold products and services by clicking on the "Secure Payment"
button below.
-
Online Visa, MasterCard,
American Express, or Discover Card payment through
PAYPAL
Online Product Catalog/Shopping Cart.
You can pay for
our mold products and services online with your
Visa, Master Card, American Express Card, or
Discover Card by clicking on the checkout button below.
-
CHECKING ACCOUNT or Credit Card payment
through
PAYPAL.
You can pay for
our mold products and services online from your CHECKING ACCOUNT
with your Visa, Master Card, American Express, or Discover card by
logging in to your
Paypal account and sending your payment to
moldinspector@yahoo.com. If you are not yet a member, you can easily
sign-up at the
Paypal website.
You can
also benefit from the
Entire Mold Library three $49-worth mold books for only $98
if you use
Paypal.
-
Purchase online using
Visa,
MasterCard, American Express, Discover card, JCB, & Diners Club Payment.
You can
buy our mold products and services online from 2Checkout.com, using
Visa, Master Card, AMEX, Discover Card, JCB,
or Diners Club by clicking on the checkout button below.
2Checkout.com,
Inc. is an authorized retailer of goods and services provided by Mold
Mart.
-
Order by
FAX with your Credit Card.
You can pay for
our mold products and services with your Credit Card through our
FAX Order Form.
-
PLACE YOUR PHONE ORDER FOR MOLD
PRODUCTS OR SERVICES,
OR ASK YOUR MOLD PRODUCTS AND SERVICES QUESTIONS THRU THE FREE
YAHOO MESSENGER WITH VOICE!
 You
can use the FREE Yahoo Messenger with Voice to place your order or
ask your questions about mold testing and remediation products and
services. To do so, simply log-in to Yahoo Messenger and add
moldinspector@yahoo.com in
your contact list. To start talking with our sales representative,
please roll your mouse over
moldinspector@yahoo.com on your Messenger List and click on the
“call” button. For details, please visit
Yahoo Messenger Voice! No Yahoo! ID yet? Please sign up at
Yahoo! website.
Alternatively, you can place your
order by calling our 24/7 SALES REPRESENTATIVE.
You can buy mold and other environmental products
and services on your Visa, Master Card, American Express, or Discover
credit card by phoning Mold Mart's Phone Sales Center.
If you
are phoning from the USA/Canada, please dial
011-63-34-471-3394
If calling from
outside of USA, please phone
63-34-471-3394
For any questions about mold products
please email: moldconsultant@yahoo.com.
REFUND POLICY:
To prevent
cross-contamination by mold spores from one customer's property to another customer's
property, all products and services are sold on a non-returnable & non-refundable basis. |
|
